Matrix M100V Especificações

Matrix Matrix Boiler Only VERSION DATE: 2-7-08 1.0 SPECIFICATIONS ...3

10 Matrix Installation and Operation Instructions 3.4 Venting Clearances These are code restrictions for the location of the Flue gas vent term

11 Matrix Installation and Operation Instructions 3.6 Outdoor Venting Vent piping outside the Building is permitted under the following conditio

12 Matrix Installation and Operation Instructions 4.0 CONDENSATE DRAIN This unit produces water as a product of combustion. Much of this water co

13 Matrix Installation and Operation Instructions 5.0 INSTALLING GAS PIPING 5.1 Installation Refer to the current National Fuel Gas Code ANSI Z22

14 Matrix Installation and Operation Instructions Table 5.1 Normal Range of Combustion Products (At maximum fan speed, 240) Natural P

15 Matrix Installation and Operation Instructions WARNING THIS APPLIANCE CONSISTS OF A “LOW-MASS” BOILER AND MUST HAVE ADEQUATE WATER FLOWING THR

16 Matrix Installation and Operation Instructions 6.1 Plumbing (Minimum Requirements) Pressure Regulator “Fill Valve” (Supplied): The Matrix op

17 Matrix Installation and Operation Instructions 6.2 Matrix Boiler Connections 6.3 Hydronic Heating Additions (Optional) ATTENTION 1. LOW TEMP

18 Matrix Installation and Operation Instructions The Matrix provides heat to hydronic heating systems in two ways: Hydronic Call (24 VAC @ H wi

19 Matrix Installation and Operation Instructions 6.3.1(B) Multiple High Temperature Zones (Zone Valves) – Wiring w/ Zone Controller 6.3.1(C) Mu

2 Matrix Installation and Operation Instructions WARNING THIS APPLIANCE INCORPORATES A CERTIFIED LOW PRESSURE BOILER, WHICH MUST OPPERATE WITH

20 Matrix Installation and Operation Instructions 6.3.2(A) Multiple High Temperature Zones (Zone Circulators) 6.3.2(B) Multiple High Temperatu

21 Matrix Installation and Operation Instructions 6.3.3 Multiple Controlled-Temperature Zones (Tempering Valves) • Use wiring configuration i

22 Matrix Installation and Operation Instructions 6.3.4(B) Single Controlled-Temperature Zones (Injection System) – Wiring Tekmar 356 6.3.5 Mult

23 Matrix Installation and Operation Instructions 7.0 Domestic Hot Water System 7.1 Operation and Set-up The Ma trix hea ts domestic hot water

24 Matrix Installation and Operation Instructions acid. Pump the cleaning liquid through the exchanger. For optimum cleaning, the cleaning sol

25 Matrix Installation and Operation Instructions 7.1.1 Matrix DHW without Storage The Matrix will provide domestic hot water continuously w he

26 Matrix Installation and Operation Instructions 8.0 WIRING 8.1 Field Wiring to Matrix All wiring must be in accordance with the Canadian Elec

27 Matrix Installation and Operation Instructions 8.2 Matrix Factory Wiring Schematic 8.2.1 Boiler Control Wiring Consult diagram on unit for ex

28 Matrix Installation and Operation Instructions 8.2.2 Fan Control Wiring Consult diagram on unit for exact wire routing.

29 Matrix Installation and Operation Instructions 9.0 CONTROL SETUP The Matrix used two devices to control the functions required by the Matrix.

3 Matrix Installation and Operation Instructions 1101201301401501600-2000 3000 4000 5000 6000 7000 8000 9000 10000Elevation (ft)Input (Mbh)Figure

30 Matrix Installation and Operation Instructions 9.2 Operation and Set-up The Matrix employs a pneumatic modulation system. This modulation sys

31 Matrix Installation and Operation Instructions 9.2.2 Setting Matrix Fan Control Just as the Matrix Boiler Controller controls all of the ope

32 Matrix Installation and Operation Instructions 9.3 Outdoor Sensor Operation The outdoor sensor is connected to the terminal board on the lef

33 Matrix Installation and Operation Instructions 10.0 MATRIX BLOWER OPERATION 10.1 Forced Air Heating The Matrix forced-air heating module is

34 Matrix Installation and Operation Instructions Optional Stage 2 Heat - W2Typical Thermostat24V Hot - RCooling - YSpace Heat - WCirculating Fa

35 Matrix Installation and Operation Instructions 11.0 HEAT RECOVERY VENTILATION 11.1 Ventilation Needs With the evolution toward more energy e

36 Matrix Installation and Operation Instructions 11.2 Types of Installation There are two basic methods of installing the ventilator in the Ma

37 Matrix Installation and Operation Instructions 11.3 Damper Box Included in the installation kit is a damper box. This damper box elimina

38 Matrix Installation and Operation Instructions ATTENTION The HRV balance must be checked and if necessary rebalanced every time the Heating (

39 Matrix Installation and Operation Instructions Menu Item Description Sample HRV Ventilation Rates Installed Ventilation Rates Installed Fa

4 Matrix Installation and Operation Instructions 2.0 INSTALLATION REQUIREMENTS The installation of your NY Thermal Matrix gas furnace/boiler must

40 Matrix Installation and Operation Instructions 12.0 LIGHTING BOILER 12.1 Initial Start-Up Ensure that the boiler is wired in accordance with

41 Matrix Installation and Operation Instructions 13.0 TROUBLE SHOOTING This section is intended to assist the service technician in detecting a

42 Matrix Installation and Operation Instructions Symptom Detected Problem Solution AL1 Communication Error with HRV 1. Check wiring co

43 Matrix Installation and Operation Instructions Symptom Detected Problem Solution Boiler will not stay lit. Indicates lack of a flame signal.

44 Matrix Installation and Operation Instructions Figure 13.2 M atrix Thermistor Resistance Chart1 Mohm Water Probe (Hi Temp.)02040608010012016

45 Matrix Installation and Operation Instructions 14.0 SEQUENCE OF OPERATION Boiler in standby modeFurnace Controlcloses T-C circuit.Furnace

46 Matrix Installation and Operation Instructions 15.0 INSTALLATION CHECKLIST Installation Connect all plumbing, and ensure that there are no s

47 Matrix Installation and Operation Instructions 16.0 ANNUAL MAINTENANCE AND INSPECTION This unit requires very little maintenance, however a Q

48 Matrix Installation and Operation Instructions No. P.N. Description1 82657 Premi x burner, 135.81A 82761 Premix Burner Gasket2 83190 Transfor

49 Matrix Installation and Operation Instructions 18.0 WARRANTY What is Covered. We the manufacturer, warrant that any parts or components of

5 Matrix Installation and Operation Instructions IMPORTANT CLEARANCES For proper and safe installation adhere to the following clearances to com

6 Matrix Installation and Operation Instructions 3.0 VENTING The NY Thermal Matrix is a high efficiency condensing gas furnace/boiler utilizing i

7 Matrix Installation and Operation Instructions 3.1 Vent Pipe Material 3.2 Venting Configurations 3.2.1 Two-Pipe Vent Termination IMPORTANT F

8 Matrix Installation and Operation Instructions 3.2.2 Concentric Vent Termination (No longer approved for Canada) Use NTI part # 82666 or York

9 Matrix Installation and Operation Instructions Figure 3.5 Installing Venting Below Grade 3.3 Venting Rules and Guidelines 1. It is highly rec