Matrix T7x Manual de Serviço

T 7 X - 0 3 T R E A D M I L LS E R V I C E M A N U A L

73.4 AUTO CALIBRATION INSTRUCTIONSRun Auto Calibration to calibrate the incline parameters after assembly and after replacing any electronic component

84.1 T7X-03 CONSOLE DESCRIPTIONThe Matrix treadmill is inspected before it is packaged. It is shipped in four pieces: the base, the upright console s

94.2 MANUAL WORKOUT OPERATIONQUICK START OPERATIONPresstheGOorQUICKSTARTbutton(s)andthetreadmillwillenter into a manual mode of operation.

104.4 HEART RATE CONTROL WORKOUT OPERATIONYour Matrix treadmill offers a heart rate control workout mode. The heart rate control workout mode allows

114.5 FITNESS TEST WORKOUT OPERATION - CONTINUEDSUBMAXIMAL TREADMILL EVALUATION CONVERSION TABLEStage Time Converted VO2max1 1:00 31.152.1 1:15 32.552

121) To enter Manager Mode, press "ENTER, 1, 0, 0, 1, ENTER" on the number keypad ON THE CONSOLE and Manager Mode will appear on the dis-p

13FUNCTION & DEFAULTSDESCRIPTIONS MODIFIEDVersions The software version is not editable, for viewing only. Cannot be modifiedKeySoundDefault: O

14FUNCTION & DEFAULTS DESCRIPTIONS MODIFIEDMaximum TimeDefault: 60 MinutesThis option enables clubs to set the maximum workout duration limits dur

15FUNCTION & DEFAULTS DESCRIPTIONS MODIFIEDDefault LevelDefault: 1This option controls the default program level. Maximum: 1Minimum: 20Default W

16MANAGER MODE FUNCTION & DEFAULTS DESCRIPTIONS MODIFIEDLanguage Select Default Language This option allow the user to select the flag for the spe

CHAPTER 1: SERIAL NUMBER LOCATION ... 1CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS 2.1

17FLAG UNITKMKMKMKMKMKMKMKMFUNCTION & DEFAULTS DESCRIPTIONS MODIFIEDDefault ChannelDefault: 3This option controls the default TV channel on start

181) To enter Engineering Mode, press "ENTER, 2, 0, 0, 1, ENTER" on the number keypad ON THE CONSOLE and Engineering Mode will appear on t

19ENGINEERING MODE FUNCTION & DEFAULTS DESCRIPTIONS MODIFIEDStatistics This option displays workout information. N/A6.3 ENGINEERING MODE - TAB 2

20ENGINEERING MODE FUNCTION & DEFAULTS DESCRIPTIONS MODIFIEDClubsDefault: MATRIXThis option allows the user to select the screen header from a lis

211) To enter Service Mode, press "ENTER, 3, 0, 0, 1, ENTER" on the number keypad ON THE CONSOLE and Service Mode will appear on the displ

22FUNCTION & DEFAULTS DESCRIPTIONS MODIFIEDMachine Type Treadmill This option allows the user to select the current model. N/ASerial Number Thi

23FUNCTION & DEFAULTS DESCRIPTIONS MODIFIEDKeypad This option is for a keypad test. N/AAuto Calibration This option is to calibrate the incline p

247.4 SERVICE MODE - TAB 3SERVICE MODE FUNCTION & DEFAULTS DESCRIPTIONS MODIFIEDDate & Time This option is to set the current date and time on

257.5 SERVICE MODE - TAB 4SERVICE MODE FUNCTION & DEFAULTS DESCRIPTIONS MODIFIEDLog This option record key component replacement history. N/ACHA

268.1 ELECTRICAL DIAGRAMCHAPTER 8: TROUBLESHOOTING

III8.14 Troubleshooting - Heart Rate Issues ... 388.15 Troubleshooting - Spee

278.1 ELECTRICAL DIAGRAMSP29 -- Console Communication WireCHAPTER 8: TROUBLESHOOTING

28N95 -- UCB Little Board Wire8.1 ELECTRICAL DIAGRAMSCHAPTER 8: TROUBLESHOOTING

29N97 -- Hand Pulse Wire8.1 ELECTRICAL DIAGRAMSCHAPTER 8: TROUBLESHOOTING

308.2 MCB LED INSTRUCTIONSLED REFERENCE DESIGNATOR DESCRIPTIONRS485 DSP2Indicates if the digital communication is working normally between the console

318.3 MCB WIRINGTB1 - AC Motor Cable SocketTB2 - Input Power Cable SocketJ9 - Inside Fan Cable SocketJ10 - Digital Communication Cable SocketJ12 - Ele

328.4 ERROR MESSAGES ON THE CONSOLECLASS LEVELERROR CODEDESCRIPTIONB 0140 Incline motor operation fail. B 0141 Motor over temperature. C 01A0 Incli

338.5 0140 / 01A0 / 01A2 ERROR TROUBLESHOOTINGERROR MESSAGES 0140 / 01A0 / 01A2 1) SYMPTOM: a. 0140 - Incline motor operation failed.

348.6 01A3 ERROR TROUBLESHOOTINGERROR MESSAGE 01A31) SYMPTOM: a. Motor is disconnected. 2) SOLUTION: a. Check the connection o

358.8 01AD ERROR TROUBLESHOOTINGERROR MESSAGE 0X029F1) SYMPTOM: a. Motor over temperature. 2) SOLUTION: a. Check the connection

368.10 02B2 ERROR TROUBLESHOOTINGERROR MESSAGE 02B21) SYMPTOM: a. The emergency circuit on the interface board active. 2) SOLUTION:

11.1 SERIAL NUMBER LOCATIONCHAPTER 1: SERIAL NUMBER LOCATION

378.12 04A0 ERROR TROUBLESHOOTINGERROR MESSAGE 04A01) SYMPTOM: a. No communication received. 2) SOLUTION: a. If the display is

388.13 TROUBLESHOOTING - NO POWER TO THE CONSOLE1) SYMPTOM: a. The unit is not getting power from the outlet. b. The MCB is no

398.14 TROUBLESHOOTING - HEART RATE ISSUESCHAPTER 8: TROUBLESHOOTINGHEART RATE ISSUES1) SYMPTOM: a. No heart rate. b. No or high he

408.15 TROUBLESHOOTING - SPEED SHOWN IS SLOWER THAN BELT SPEED1) SYMPTOM: a. The unit speed does not match the console display. 2) SOLUT

411. Sections 8.16-8.19 will help with diagnosing problems with TV and entertainment related equipment that is produced by Matrix Fitness Systems. .

428.17 ENTERTAINMENT TROUBLESHOOTING – PICTURE FUZZY OR UNCLEARNOTE: If the internal TV is having reception issues (for example if channels only come

431. If you have no picture at all check to see if you have any status lights on your controller or TV. Status lights should be red when off or in

441. If you have status lights on the TV, but the On / Off button gives no response, disconnect and then re-connect the power to the treadmill

459.1 MOTOR COVER AND LOWER SHROUD REMOVAL1) The motor cover is split into two pieces (called the motor cover and lower shroud 2) Remove the 2 screw

469.2 REAR ROLLER REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove the 4 screws holding on both of the end caps

22.1 BEFORE GETTING STARTEDThis treadmill is intended for commercial use. To ensure your safety and protect the equipment, read all instructions befo

479.3 RUNNING DECK REPLACEMENT 1) Remove the motor cover as outlined in Section 9.1. 2) Remove the four running deck screws using a 5 mm Allen wren

489.4 RUNNING DECK CUSHION REPLACEMENT 1) Remove the running deck as outlined in Section 9.3. 2) Hold the running deck cushion bolt with a 5 mm Al

499.5 FRONT ROLLER REPLACEMENT 1) Remove the motor cover as outlined in Section 9.1. 2) Using a hook or loop of wire, remove the spring from the d

509.6 RUNNING BELT REPLACEMENT1) Remove the motor cover as outlined in Section 9.1. 2) Remove the rear roller as outlined in Section 9.2. 3) Remo

519.7 SIDE RAIL REPLACEMENT1) Remove the 4 screws holding on the end cap on the same side as the broken side rail using a Phillips screwdriver and re

529.8 MOTOR CONTROL BOARD (MCB) REPLACEMENT 1) Turn off power and disconnect the cord from the machine. 2) Remove the motor cover as outlined in Se

539.9 MOTOR REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Remove the motor cover as outlined in Section 9.1. 3) R

549.10 DRIVE BELT REPLACEMENT1) Remove the motor cover as outlined in Section 9.1. 2) Release the drive belt tensioner from the drive belt as outli

559.11 INCLINE MOTOR REPLACEMENT1) Turn off the power and disconnect the cord from the machine. 2) Lift the treadmill and support it so that the fr

569.11 INCLINE MOTOR REPLACEMENT - CONTINUEDFIGURE D FIGURE EFIGURE F FIGURE G5) Disconnect the incline motor power cable from the MCB (Figure D). 6

3CAUTION: If you experience chest pain, nausea, dizziness or shortness of breath, STOP exercising immediately and consult a physician before continui

579.12 CONSOLE REMOVAL1) Turn off the power and disconnect the cord from the machine. 2) Remove the 4 screws holding the console back to the front

589.13 CONSOLE MAST ARM REPLACEMENT 1) Turn off power and disconnect the cord from the machine. 2) Remove the console as outlined in Section 9.12.

599.13 CONSOLE MAST ARM REPLACEMENT - CONTINUEDFIGURE H FIGURE IFIGURE JFIGURE K7) Remove the screws holding the console frame to the mast arms with

609.14 CONSOLE CABLE REPLACEMENT 1) Turn off power and disconnect the cord from the machine. 2) Remove the console as outlined in Section 9.12. 3)

617) Remove the spiral protective wrap from the top and bottom portions of the wire harness (Figures H & I). FIGURE H FIGURE I9.14 CONSOLE CABLE

629.15 HANDLE BAR SERVICE1) Turn off the power and disconnect the cord from the machine. 2) All items on the handle bar are removed using a Phillip

639.16 EMERGENCY STOP SWITCH REPLACEMENT1) Turn off power and disconnect the cord from the machine. 2) Remove the console as outlined in Section 9.1

649.17 HEART RATE BOARD REPLACEMENT1) Turn off power and disconnect the cord from the machine. 2) Remove the console as outlined in Section 9.12.

659.18 BLOWER MOTOR REMOVAL1) Turn off power and disconnect the cord from the machine. 2) Remove the console as outlined in Section 9.12. 3) Lay

661) Turn off power and disconnect the cord from the machine.2) Remove the console as outlined in Section 9.12. 3) Remove the back cover of the co

4For your safety and to ensure good treadmill performance, the ground on this circuit must be non-looped. Please refer to NEC article 210-21 and 210-2

679.19 OVERLAY REPLACEMENT - CONTINUEDFIGURE F FIGURE GFIGURE H9) Match the overlay to the cutout on the console (Figure F). 10) Press down on the

68CHAPTER 10: TREADMILL SPECIFICATIONS AND ASSEMBLY GUIDE10.1 TREADMILL SPECIFICATIONSFEATURESDeck Type Ultimate Hard-Wax reversible 1" deckBelt

69Part #: Part Name: Outline: Dimensions: Quantity: Bag Color:10 020090-00 Socket head cap screw M8 x 20mm 10 Black14 0000086571 Flat Washer 6.2 x 12

7010.3 ASSEMBLY INSTRUCTIONSATTENTIONAfter assembly and installation is complete, the treadmill will need to be calibrated using the auto-calibration

7110.3 ASSEMBLY INSTRUCTIONS - CONTINUEDOpen White Assembly Bag. Assemble the left and right bracket (items 20 and 21) to the console base using item

7210.3 ASSEMBLY INSTRUCTIONS - CONTINUEDOpen Red Assembly Bag. Assemble the console base to the console masts using item 15 button head cap screw and

7310.3 ASSEMBLY INSTRUCTIONS - CONTINUEDOpen Green Assembly Bag. Install the power cord and assemble item 18 power cord holder with item 22 button he

7410.4 LEVELING THE TREADMILLOPTIONAL LEVELING ASSEMBLY TECHNIQUES: USE OF SHIM OR BY ADDING A LEVELING FOOT.Note: It is extremely important that th

7510.5 ENTERING THE SERIAL NUMBERS INTO THE CONSOLEONCE INSTALLATION IS COMPLETE, THE CONSOLE AND PLATFORM SERIAL NUMBERS SHOULD BE ENTERED INTO THE C

7610.6 TV PROGRAMMING INSTRUCTIONSOnce the cardio equipment has been installed, and proper power and cable wiring is provided, The Television must be

5Preventative maintenance and daily cleaning will prolong the life and look of your MATRIX treadmill.Please read and follow these tips.• Positiont

77Auto Scan (continued):9. If the channels are not coming in clearly after a channel scan (or if only some channels come in), follow Steps 4-7 to ent

78Closed Caption - Clubs will vary on whether they request the closed caption to be turned off or on. Please discuss this option with the club manage

7911.1 SOFTWARE UPGRADE INSTRUCTIONS1)FivefilesshouldbepresentontheUSBdrive.TheseareSirF7xAll.cab,NK,IO_XXX,updateLMM.cofige,andExt

8011.1 SOFTWARE UPGRADE INSTRUCTIONS - CONTINUED5) When the update is complete, the display will ask you to remove the USB drive (Figure E). Once th

81NOTES

82MATRI X FITN ES S SY ST EM S CO RP.161 0 LA ND MARK D RI VE COT TAG E GR OV E WI 53 527 US ATO LL FRE E 86 6. 69 3. 48 63 w w w. m a t

63.3 CARE AND MAINTENANCE INSTRUCTIONSIn order to maximize life span, and minimize down time, all Matrix Fitness System's equipment requires regu